Looking for exceptional sound over IP? The 4430A offers power, audio and loudspeaker management via a single standard CAT cable, delivering unrivalled flexibility, cost-effectiveness and simplicity of installation.
4430A
Smart IP Installation Speaker
SPL
104 dB
Amplifier Power
50 W Bass (Class D) + 50 W Treble (Class D)
Frequency Response
45 Hz - 39 kHz (-6 dB)
Accuracy of Frequency Response
± 1.5 dB (58 Hz - 20 kHz)
Driver Dimensions
⌀ 130 mm Woofer + ⌀ 19 mm Tweeter (view in inches)
Dimensions
H 285 x W 189 x D 178 mm, (view in inches)
Weight
5.1 kg / 11.2 lb
Connections
1 x RJ45 AES67 / Dante Input
1 x Euroblock Analog Input
Color options:
4430A Smart IP Installation Speaker
Technical Specifications
Looking for exceptional sound over IP? The 4430A offers power, audio and loudspeaker management via a single standard CAT cable, delivering unrivalled flexibility, cost-effectiveness and simplicity of installation.
System Specifications
Frequency Response
58 Hz - 20 kHz (± 1.5 dB)
Low cutoff -6dB
45 Hz
High cutoff -6dB
39 kHz
SPL
Peak SPL
≥107 dB
Maximum peak acoustic output per unit in a listening room with music material, at 1 m, using PoE+ power.
Short term max SPL
≥104 dB
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
Long term max SPL
≥96 dB
Maximum long term RMS acoustic output in same conditions with IEC weighted noise (limited by driver unit protection circuit) at 1 m.
Self-generated noise
Self-generated noise
≤5 dB
Self generated noise level in free field at 1m on axis(A-weighted).
Weight
Weight5.1 kg (11.2 lb)
Dimensions
Height
285 mm
(11 1/4 in)
Width
189 mm
(7 1/2 in)
Depth
178 mm
(7 in)
Enclosure
Enclosure material
Die cast aluminium
Enclosure type
Reflex port
Drivers
Woofer
Driver type
Cone
Diameter
130 mm
(5 1/8 in)
Tweeter
Driver type
Metal dome
Diameter
19 mm
(3/4 in)
Directivity
Vertical directivity
Horizontal directivity
Harmonic distortion
50…200 Hz ≤2 %
> 200 Hz ≤0.5 %
> 200 Hz ≤0.5 %
Group delay
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
2.3 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Amplifier Section
Amplifiers
4430A bass amplifier
50 W Class D
4430A treble amplifier
50 W Class D
Mains voltage
PoE+/PoE
Power consumption
ISS Active
≤4 W
Idle
≤5 W
Full output
25.5 W
Signal processing section
Connectors
Input
Ethernet (Power over Ethernet and Audio over IP)
Input
Audio input is via a 10 kOhm balanced connector.
Crossover
Bass/Treble
2900 Hz
Product Variants
Product codes
Code
Product information
EAN code
CN code
4430A Smart IP Installation Speaker Black
4430A Smart IP Speaker White
4430A RAL Colors
4030C Installation Speaker RAW
